Most packaging machine faults trace back to a short list of causes: seal settings that no longer suit the film on the machine, uneven web tension, a doser still set for a product that has changed, worn knives and jaws, sensors that are dirty or knocked out of line, wet compressed air, and connections shaken loose by vibration. The machine itself is rarely the first suspect — the product, the film and the services feeding the machine usually changed first.
The process at the end is how to work through a fault that is not on the list.
Poor sealing is nearly always a mismatch between the three jaw settings — temperature, dwell time and pressure — and the film actually on the machine, or product trapped between the two layers. Check those before suspecting the jaws.
The sealant layer has to melt through the outer layers of the laminate, so what matters is the heat arriving at the interface, and that is set by temperature and dwell together. Raising line speed shortens dwell, which is why a temperature that sealed perfectly at a lower speed produces weak seals once the operator turns the machine up. Pressure is the setting people reach for first and it helps least: once the two films are in full contact, more force only thins the seal and wears the jaws.
A seal that is strong on one side and weak on the other is the jaws, not the settings: faces out of parallel, worn PTFE tape, or a heater cartridge or thermocouple failing in one jaw. A seal that comes and goes on the same lane with nothing changed is contamination — powder or oil settling in the seal zone before the jaws close. The fix is upstream, in fill timing and dust extraction; more heat only bakes the contaminant in.
When a roll changes, treat the seal window as unknown. Sealant grade and thickness vary between film suppliers and between lots, and the settings one roll accepted can be wrong for the next.
Film that walks sideways on the former means the web tension is uneven across its width, and the edge guide is the last thing to adjust, not the first.
Film runs toward the slack side. A roll not square on the unwind shaft, a core that has slipped, or an idler roller knocked out of parallel loads one edge more than the other, and the web drifts away from it. On a vertical machine the pull belts do the same: one belt worn or set softer than the other drags the film round the forming tube, and the back seam wanders from bag to bag.
Work from the roll forward. Square the roll and lock the core, check each roller with a straightedge, equalize pull-belt pressure and look at belt wear, and only then re-teach the edge guide. A roll wound with a telescoped or wavy edge cannot be tracked by any sensor; reject it to the film supplier rather than chasing it.
Filling weight goes wrong when the product changes and the doser does not. An auger or cup filler delivers a volume, so any shift in bulk density — a new batch, a damper day, a hopper running low and letting the powder loosen — shows up directly as weight. Check the product and the hopper level before you touch the filler.
Keep the hopper within a narrow level band: an auger draws from the head of powder above it, and a hopper swinging between full and nearly empty gives a dose that swings with it. On liquids the equivalent is temperature; viscosity moves with it, and a pump set on a cold product overfills once the line warms up.
A multihead weigher weighs rather than doses by volume, so its drift means something else — product stuck in the buckets, a load cell holding a zero offset after washdown, or vibration from a neighbouring machine reaching the weigh heads.
The target you set is nominal plus your spread, so every fix that narrows the spread is giveaway you can take back. An in-line checkweigher makes the spread visible while you work on it: the trend on its display shows whether a change helped within a few minutes.
A jam is almost always a pitch or geometry mismatch: the product arriving at the infeed is longer, taller or more skewed than the machine was set for, or it is arriving faster than the machine takes it away.
On a flow wrapper the infeed lugs are spaced for one product length. A product that has grown — a bakery item that proofed longer, a tray with its lid slightly off — fouls the former or the fin-seal wheels, and a product laid crooked on the belt does the same. Where the upstream machine outruns the wrapper, product piles up at the transfer and gets pushed in two at a time.
On a vertical or sachet machine the jam is inside: product bridging in the hopper, a sticky or static-charged product hanging in the forming tube, and pieces dropping late into the closing jaws. An ionizing bar handles light product clinging to the film; an agitator handles bridging.
Check the product dimensions against the recipe first, then infeed speed against the upstream machine, then clean. Dust building up on guides and in the forming tube narrows the path a little every hour, and by the end of a shift a product that ran freely at the start no longer fits.
Film tears where something in the web path is cutting or over-stressing it, and tension is the force doing the tearing — so back off the tension and inspect the path before you change the film.
Run a finger along the forming shoulder, the former edges and every roller the film touches. A scored shoulder or a burr on a roller nicks the edge, and the nick becomes a tear as soon as the machine pulls. A roller whose bearing has seized drags the web instead of turning with it and adds tension nobody set. On the unwind, a brake set too hard or a dancer loaded too heavily does the same across the full width, and a misaligned roll puts all of it on one edge.
A break that always comes at the same point in the roll is the roll: a bad splice, or film gone brittle in cold storage. Bring cold film up to room temperature before it goes on the machine, and re-make splices flat with tape across the full width — a lifted splice edge catches on the former.
A registration failure is one of two things: the sensor is not seeing the mark, or it sees the mark and the film still moves after it. Which one it is decides whether you work on the sensor or on the drive.
The eye-mark sensor reads contrast between the mark and the film around it. A new print run with a paler mark, a metallized film throwing glare, a lens coated in film dust, or sun through a doorway hitting the sensor face can all take the contrast below what it was taught on. Re-teach on the film that is actually running, clean the lens, shade the sensor, and check the mark position against the artwork; a mark printed off the repeat cuts through the graphic whatever the sensor does.
If the mark is read cleanly and the cut still drifts, the film is slipping after the sensor: worn or oily pull belts, a loose drive roller, or a bag length in the recipe that does not match the print repeat, so the machine hunts back to the mark every cycle. A clean, steady cut with the mark in the wrong place is a print problem, not a machine problem.
Cutting faults come from the blade and its gap to the anvil, or from the knife acting before the film is held still. A blade going dull shows itself first as hairs and thread tails on the cut edge, well before it starts leaving bags joined.
Check the gap and the edge before anything else. A knife set too far from its anvil folds the film instead of cutting it; too close, and the two edges wear each other down within a shift. A film change is the moment to ask whether the blade type still suits the structure — a thick or metallized laminate that a straight blade handled at one thickness can defeat it at the next, and a serrated blade holds film that would slide away from a straight edge.
A clean cut in the wrong place, or a small uncut tab left on one side, is timing: the knife is firing while the film is still moving, or before the jaws have clamped it. Any product in the cut zone gives a ragged cut and a bad seal together; when those two symptoms arrive at once, treat them as a fill-timing problem, not a knife problem.
Most sensors reported as faulty are working and reporting a condition that has changed — dust on the optics, a bracket that vibration has walked out of alignment, or a target the sensing mode was never suited to. A dead sensor is the rare case.
Start with the indicator light on the sensor body. Put the target in front of it by hand and watch the output LED: if it switches, the sensor is fine and the fault is in the wiring, the input card or the program’s expectation of it. If it does not, clean the lens and re-aim before you replace. Sensor brackets are light and cantilevered, so vibration loosens them faster than any other fastener on the machine; mark the aligned position with a paint pen so a drift shows at a glance.
Clear film and glossy trays fool diffuse-reflective sensors, which need a surface to bounce light off; switching to a through-beam or retro-reflective arrangement is a mode change, not a repair. Cables that flex with a moving part fail at the gland, so a sensor that drops out at one point in the cycle is a cable fault until proven otherwise.
Conveyor problems on a packaging line are usually problems at the joints between machines — a height step, a speed mismatch or a gap at a transfer — plus belt tracking. A conveyor rarely fails by itself.
At a transfer the product should arrive at the same height and close to the same speed it leaves at. Even a small step down tips a tall pack or a flat pouch onto its edge; a downstream belt running slower than the one feeding it stacks product and jams the next infeed, while a faster one opens gaps the next machine reads as missing product.
On secondary packaging lines this is the everyday case: case packers and cartoners take product in indexed groups while the primary machine sends it continuously, so the conveyor between them is a buffer and its speed has to be set from both ends, not one.
Belt tracking follows the same rule as film — the belt runs toward the slack side. Uneven tension, a return roller knocked out of square, or debris packed under one edge steers it off. Track with the tensioners at the tail, not by shimming the head, and a belt at the end of its adjustment is replaced rather than tightened further. A roller running warm is a bearing drying out, and a belt that suddenly starts wandering is often its first sign.
Timing goes out when the machine loses its reference: a home position that has drifted, a servo axis that came out of a fault stop out of phase with the others, or a changeover recipe that was not loaded in full. Jaws closing on product, the knife catching the seal and product missing its pocket are the same fault seen at three stations.
On a servo machine, re-home every axis and run empty for a few cycles. If the timing comes back, the cause was the fault stop, and the recovery routine needs looking at rather than the settings; if it drifts again while running, look at the encoder coupling, where a loose set screw lets the encoder lag the shaft a little each cycle. On a mechanical machine the equivalent is a cam that has slipped on its shaft.
After a changeover, compare the loaded recipe against the recorded one line by line — a bag length changed without its fill delay is the commonest route to product in the jaws. Between machines, timing is a handshake: a wrapper releasing into a cartoner before the cartoner has signalled ready is a mistimed signal, not a mistimed machine, and it is found on the I/O status screen, not at the tooling.
A cylinder that slows, a valve that sticks and a jaw that loses grip mid-cycle are compressed-air faults before they are component faults. Check the pressure at the machine while it is running, and check what is in the air, before you replace anything.
Read the gauge with the machine cycling, not idle. A supply that holds at standstill and sags every time the jaws actuate is a line or leak problem: a drop too small for the machine added to it, another machine drawing at the same moment, or leaks accumulated at push-in fittings.
Then drain the filter bowl on the machine’s regulator. If water comes out, the plant dryer is not keeping up, and water is what corrodes valve spools and washes the lubricant out of seals — the sticking valve is the symptom.
Electrical and control faults are dominated by connections rather than components: terminals loosened by vibration, a safety circuit opened by one of its many switches, and sensor signals picking up noise from a motor cable run beside them. Start at the fault code on the HMI, and read the whole fault history rather than clearing the current alarm.
An emergency-stop or safety fault means one device in a chain has opened — a guard switch on a door not quite shut, a pull-cord knocked, a light curtain someone leaned into — and the HMI usually cannot say which. Walk the chain instead of resetting repeatedly.
A drive or servo alarm for overcurrent or following error points back to the mechanics: a bind, a seized bearing, a jam the drive is trying to push through. Fix the load before suspecting the drive.
Faults that appear at speed and vanish at rest are loose terminals or a chafed cable, and the way to find them is a check of every terminal in the panel with the power isolated. Sensor signals that flicker when a motor starts are a noise problem: check the shield earthing on the signal cable and get it out of the tray it shares with the motor cable.
The process is the same for every fault above: read the symptom, ask what changed, isolate the machine before your hands go in, narrow the fault to one station, change one thing at a time, and prove the fix with a measurement before you record it. Skipping a step costs more time than the step takes.
The rejects tell you the station. A seal weak on one side is a jaw; hairs on the cut edge are a blade; a cut wandering across the graphic is registration; a bag heavy, then light, then heavy is the hopper level. Read the fault history on the HMI as well as the current alarm, and note when the fault started and how many packs it affects — an intermittent fault and a constant one have different causes.
Most faults follow a change: a new film roll, a new product batch, a changeover, a washdown, a new operator, another machine added to the air line, a hot afternoon. Ask the operator directly and check the roll and batch labels. This question closes more faults than any instrument, and it is the one most often skipped.
Before a hand goes past a guard, isolate the electrical supply and the air, vent the stored air — cylinders hold pressure after the valve is off — and lock it. The US lockout rule, 29 CFR 1910.147, counts unjamming and adjusting as servicing, not as routine operation; whatever the rule where your plant stands, a jaw closing on a hand does what it does to film.
Run the machine empty, then with film only, then with product. A fault that disappears without product is fill timing or the product itself; one that stays with film alone is the machine or the film, and swapping in a known-good roll separates those two. On a line, stop the machines one at a time and see which stop makes the fault go away — the fault is often two machines upstream of where it shows.
Write down the starting value, make one change, run enough packs to judge it, and revert it if it did nothing. Two changes at once means you do not know which one worked, and one of them is now wrong for no reason.
Prove the fix with a number — a peel test, the checkweigher spread, a count of good packs over a run — not the look of a pack in the hand. Then write down what changed and to what value, and save the recipe. The next time the fault appears, and it will, the record turns an afternoon into a few minutes.
Twelve problems, and most come back to four things: heat and dwell that no longer suit the film, tension and alignment in the web path, a product or film that changed after the machine was set, and air, sensors and connections nobody looked at because nothing was visibly broken. Work from the product and the material back to the machine, change one thing at a time, measure the result, and keep the record.

Get Your Custom Packaging Solution
Tell us about your product and production needs. Our engineers will recommend the right machine configuration for your application.
We only use your details to reply to this request.