5 Common Quality Defects on Sachet Lines (Symptom, Cause, Fix)

A sachet failing leak test at end of line is rarely a single defect — it is one of five symptoms sharing a small set of upstream root causes. Operators who reach for jaw temperature first spend shifts cooking film around problems that started at the auger, the forming collar, or a $5 strip of PTFE tape.

The five defects below are ordered by how often they get misdiagnosed. Each follows the same triage shape: symptom, cause, confirming check, fix.

1. Channel Leak From Seal-Zone Contamination (Quality Issue #1)

A sachet that looks fine at the discharge but fails a downstream leak test almost always has a channel leak. Contamination is the first place to look — not jaw temperature.

Visual checks catch seal channels down to 75 µm with only a 60-100% probability, so some leak defects pass without visible clues. ASTM F1886 visual inspection is a first-line screen only, not a pass gate.

Powder dust migrating from the auger discharge or static-charged film during unwind settles into the seal zone and acts as a physical barrier. The sealant layers cannot touch, and no chemical bond forms regardless of setpoint.

Run a thumb along the inside of the seal area. If you feel grit or powder, jaw temperature is innocent. Confirm with ASTM F3039 dye-penetration — channel leaks down to ~50 µm light up within minutes, and the dye trail points to the contamination path.

The fix is upstream: add compressed-air blow-off above the seal jaws on dusty products, fit a static eliminator over the film web to neutralize static, and inspect the auger discharge for splash. Cleaning the jaws is the symptom remedy; controlling where the powder lands is the cause remedy.

Operator inspecting sachet quality control defects by checking for powder contamination in the seal zone.

2. Wrinkled or Folded Seal Area (Quality Issue #2)

When the seal area shows a visible wrinkle or fold, the failure is upstream of the jaws. A wrinkle forms a channel leak because the leak path runs along the wrinkle, several times wider than the channel diameter the seal was designed for.

Jaws sealing through doubled or tripled film cannot bond properly even at correct temperature and dwell. Cranking temperature higher burns surrounding film without fixing the wrinkled section.

Most wrinkles trace to loose unwind tension, a worn dancer arm, or forming-collar misalignment. If the wrinkle direction is consistent across rejects, the collar geometry is wrong; if random, the tension control is drifting.

Adjust unwind tension first (most lines need 0.5-1.5 N per cm of film width), reseat the forming collar, then verify jaw parameters. Operators who default to “+10 °C and see if it holds” on wrinkle defects damage three rolls of film before realizing the wrinkle is still there.

Diagram of wrinkle-induced channel leak in sachet quality control defects, showing leak path versus flat seal.

3. Peelable or Under-Bonded Seal (Quality Issue #3)

A seal that peels apart in the operator’s hand is the cleanest defect on this list — the diagnosis is heat, dwell, or pressure, and the fix is at the jaw. The seal failed to reach activation temperature for long enough at sufficient contact pressure, so the sealant layers softened without fusing.

Pull a peeled sachet apart and look at the seal face. A glossy, unmelted surface means the jaw never reached activation temperature — increase setpoint 5-10 °C.

A partially melted surface with peel-after-some-resistance means dwell was too short — extend dwell 100-200 ms before raising temperature. A complete melt pattern with weak adhesion means contact pressure is insufficient — inspect the rubber pad behind the jaw and check pneumatic pressure.

Change one variable per trial. Operators who turn three knobs together cannot tell which fixed the seal.

Heat-dwell-pressure is the foundation of every sachet packaging machine sealing system. Quantify seal strength against an ASTM F88 peel-strength baseline so adjustments target a measurable value.

Sachet quality control defects example showing a peelable under-bonded seal with glossy unmelted surface.

4. Stringy, Burnt, or Crumbly Seal (Quality Issue #4)

A seal with stringy edges, scorched film, or a crumbly texture has an over-heat problem — but the root cause is rarely the setpoint itself.

The most common cause of stringy seals on automated sachet lines is worn or torn PTFE (Teflon) tape on the heating element. A $5 strip of tape, replaced in 60 seconds, prevents thousands of dollars in downtime.

Open the jaw guard and inspect the PTFE strip on both seal bars. Look for tears, glazed patches, or sections where the tape has shifted off the heating element.

If the tape is intact, check whether the burnt pattern is uniform. Uniform scorch suggests over-temperature (reduce setpoint 5-10 °C); one-sided scorch points to misaligned jaws pinning one section against the heater.

Replace the PTFE tape at every changeover as preventive maintenance, not corrective action.

Worn PTFE tape on sealing jaw causing stringy seal defects in sachet quality control.

5. Fill Weight Drift Across Lanes on Multi-Lane Lines (Quality Issue #5)

On a multi-lane sachet line, an aggregate checkweigher reading “in spec” can hide a single lane drifting badly out of spec — the average masks the offender. Sachet weight variance regularly exceeds the variance of a single dosed unit, so aggregate weight checks cannot resolve which lane is misfilling.

Pull 10 sachets from each lane separately, weigh them individually, and chart by lane. If one lane shows a consistent offset while the others sit on target, the auger or volumetric cup for that lane is the cause — check for product bridging, worn flights, or a stuck cup.

If all lanes drift together, the upstream feed is the cause, not the dosing.

Multi-lane sachet systems with independent lane control allow isolating the affected lane and adjusting its fill parameter while the others run on target. Lines without lane-level control need a per-lane checkweigher upstream of the seal, not an aggregate one downstream.

Multi-lane fill weight drift diagnosis for sachet quality control defects on a five-lane sachet line.

The Three Misdiagnosis Loops That Cost Shifts on QC

Three reflexes account for most of the wasted troubleshooting time on sachet quality control:

  1. Jaw temperature as the universal first knob. Contamination, wrinkles, and pressure faults do not cook away. Ask whether the symptom is heat-shaped (peel, under-bond) or upstream-shaped (wrinkle, contamination) before turning the setpoint.
  1. Visual inspection as a quality gate. ASTM F2096 internal pressurization carries only ~81% detection probability at 250 µm — even the test for gross leaks misses one in five. Mission-critical lines need a confirming method: ASTM F2338 vacuum decay for whether-it-leaks, ASTM F3039 dye penetration for where-it-leaks, ASTM F88 peel strength for how-strong. Picking one test for all three is how operators chase ghosts.
  1. Blaming the auger when an aggregate checkweigher drifts, without first proving which lane is the offender. The fix is procedural — per-lane sampling at every adjustment — not mechanical.

The broader troubleshooting discipline across packaging machinery follows the same rule: name the symptom precisely before turning a knob.

Diagnostic flow for sachet quality control defects showing three misdiagnosis loops and correct triage paths.

What Most Lines Get Wrong on QC

The most common QC mistake on sachet lines is treating each defect as a one-off, instead of building a fixed sampling cadence. The cadence that catches problems early is start of shift, once per hour, after any adjustment or material changeover, and end of shift.

The lines that run cleanest are not the ones with the best operators; they are the ones where a drifting lane gets caught at the 9 a.m. check rather than at end-of-shift count.

    Comments are closed

    Soontact provides complete packaging solutions for manufacturers worldwide. Contact our packaging engineers to discuss your specific products, production volumes, and packaging material requirements.

    We offer machine demonstrations, application testing, and detailed proposals that address your particular operational needs.

    Get Your Custom Packaging Solution

    Tell us about your product and production needs. Our engineers will recommend the right machine configuration for your application.

    We only use your details to reply to this request.